FreeCamp Car Wash Set
12 VOLT CAR SHOWER AND WASH SET
showering,
Car washing,
Washing up,
Water power is adjustable,
easy to carry,
durable and strong,
Portable shower set suitable for all interior and exterior washable purposes
The shower is delivered assembled and ready to use. A plastic cover is supplied with the product.
CONDITIONS
Parameter Units Value
Catalog No 82992
Rated Voltage 12
Rated Power M 35-60
Degree of Protection IPX8
Capacity 20
Max.water temperature 35
Hose Length 2.0
Cable Length 4.0
Pump weight 80
SAFETY INSTRUCTIONS
ATTENTION! Read all the instructions below. Failure to do so may result in electric shock, fire, or personal injury.
FOLLOW THE INSTRUCTIONS BELOW
-Do not use the product in explosive atmospheres containing flammable liquids, gases or vapors. Do not place the device near any heat or fire source.
-Connect the device only to the mains with the voltage and frequency specified on the nameplate of the device.
-The plug of the power cord must match the electrical outlet. Do not change the plug. Do not use any power adapter to insert the plug into the socket. An unmodified plug that fits into the socket reduces the risk of electric shock.
- Unplug the power cord after each application.
Never leave the product unattended if the power cord is plugged into the electrical system.
-The pump should always be submerged below the water surface during use. Running without water will cause overheating and irreversible damage to the pump.
PRODUCT OPERATION
Position the pump below the water surface so that the entire pump is submerged (Il).
Make sure the switch is in the "off" - O position. To do this, press the switch and turn it off. Plug the power cord into the electrical system.
Route the shower outlet to a safe location away from electrical appliances.
Turn the switch to the "on" position - I.
Wait until the water starts to come out of the shower outlet.
Do not pull the pump out of the water during use. In such a case, the shower will not work properly when the pump will be put back into the water. If no water is flowing from the shower after the pump is placed in the water, turn off the shower with the switch, unplug the power cord, and then hold the hose vertically so that all the water flows out (III). Place the pump below the water surface and restart the shower according to the procedure described above.
When you're done showering, turn off the shower with the on/off button. Unplug the power cord from the power outlet. Then hold the hose vertically to let the water drain out completely (III).
shower setting
The intensity of the water jet can be adjusted by turning the knob on the back of the shower head (IV). Turning the knob clockwise decreases the intensity of the water jet, and turning it counterclockwise increases the intensity of the water jet.
Lowering the lever lock locks the lever so that it does not need to be held while using the shower (IV).
The outlet of the handheld shower head is equipped with a ring that changes the type of water jet when rotated (V). The ratchet sound confirms that the ring is in the selected position.
The shower head can be disconnected from the hose via the quick coupling. Slide and hold the hose coupling, then remove the shower head (VI). Installation is done by pressing the shower head connector into the hose connector socket until you hear the latch mechanism work. Removing the shower head makes it easier and faster to drain the remaining water in the product after use. Do not disconnect the shower head while the water is running from the shower.
MAINTENANCE, TRANSPORT AND STORAGE
After use, the water of the product should be completely drained. This will prevent the growth of microorganisms in the water system and will also prevent damage to the product by freezing water.
Unscrew the pump holder and pull out the sponge filter (VII) of the pump. Rinse the filter and holder with warm running water, then dry and reattach to the pump. It is forbidden to use the pump without the filter installed.
After cleaning the outer surfaces of the product with a slightly damp cloth, dry it or leave it to dry.
The product should be transported and stored in the supplied case. Store the product in shaded and well-ventilated places. The storage location should prevent unauthorized access to the product.
